发布时间：2015-04-03 来源：人大经济论坛

轻化工程专业论文范文 目 录 年产3.5万吨装饰原纸造纸综合工厂设计 annual production capacity of 35,000 tons paper decorative integrated plant design 目 录III 1 绪论1 1.1 设计题目1 1.2 设计的原始数据1 1.3 产品规格及技术指标2 1.4 建厂可行性分析2 2 工艺部分4 2.1 全厂总平面图的介绍与分析4 2.2 工艺流程62.3 工艺条件及工艺参数选择9 2.4 抄纸车间浆水平衡计算10 2.5 原材料、蒸汽及水的单位耗用量15 2.6 车间副产品及废物处理方法17 2.7 主要工艺设备的选型计算及说明17 2.8 车间布置说明19 3 辅助专业设计19 3.1 厂房建筑与结构19 3.2 给水和排水20 3.3 动力、蒸汽及采暖通风21 3.4 环境保护与综合利用22 3.5 劳动安全卫生24 3.6 抄纸车间的工作制度，车间定额及人员编制25 4 设计总结26 致谢27 参考文献28 摘 要：本次设计主题是年产3.5万吨装饰原纸综合工厂设计，主要内容是抄纸车间的工艺流程设计以及各工段工序设备图(车间布置图等等)，还包括全场总平面布置图。总的一个设计思路主要围绕装饰原纸这一特种纸张它的特点以及自身属性，来定这一纸种的生产原料和设备选型及布置，我在这次设计中主要运用书本及装饰原纸生产厂家这两大部分采集资料，再涵盖自己的思想，在老师的悉心指导下完成此文。首先我介绍了装饰原纸的产品规格以及技术指标以及建厂的可行性分析，这是作局为一个设计能否符合国家以及成品有效性的规定所要求的先决条件，也是设计的一个标准。然后是一些环保上的要求，充分考虑废水、废气、废渣的循环利用，还有总平面设计的一些技术指标。接着是介绍装饰原纸的工艺流程以及浆水平衡的计算，原材料蒸汽及水的耗用量。最后是介绍抄纸车间的工作制度，车间定额以及人员编制。以上提到的内容都与此次设计能否作为工厂正常实施可用必须的一个理论依据。 关键词：装饰原纸；抄纸车间；设计依据；综合工厂设计 Annual production capacity of 35,000 tons decorative paper integrated plant design Abstract: The design theme is decorative base annual production capacity of 35,000 tons a comprehensive plant design, the main contents of the paper-making workshop as well as the process design process equipment diagram section (shop layout, etc.), but also including the overall floor plan. A total design focus on the special paper base paper decorative features, as well as their own property, to set the paper types of production materials and equipment selection and layout, I am in the design of the main use of books and decorative base paper manufacturer Most of the information collected in these two, and then covered his own ideas, the teacher under the guidance of this article. First of all, I introduced the decorative paper product specifications and technical indicators, as well as the feasibility of plant analysis, it is a possibility of a design bureau for the national as well as the finished product required by the provisions of the effectiveness of pre-conditions, but also a standard design. Followed by a number of environmental protection requirements, take full account of wastewater, waste gas, waste residue recycling, as well as the overall graphic design of a number of technical indicators. Decorative base paper is then introduced, as well as the process of calculating the balance serofluid, raw materials, steam and water consumption. Finally, there is introduced the system of paper-making workshop, workshop fixed and staffing. Content mentioned above are related to the design of the normal operation of whether the plant can be used as a theoretical basis for the need. Keywords : decorative paper；Paper-making workshop；design based on；integrated plant design